Инсталиране на Vediamo 5

!!!БЕЛЕЖКА: Всичко написано отдолу е опит с Veidamo 4.02.02!!!
Ако вече си го инсталирал, трябва да го активираш, с което не мога да ти помогна.
Ако вече обаче е активирано, трябва да редактираш .ini файла с настройките на портовете.
Във Vediamo 4 това става като отидеш в:
C:\Program Files\Vediamo\Caesar\driver и отвориш файла slave.ini
Там има за Part D, Part J и т.н.
За Part D аз сменям com=2 и ми разпознава стара.
Виж дали това би ти помогнало
Прикачам файла както е в момента, не съм правил още промени.
Имам и един друг въпрос - в настройките имам CBF и CFF данни. Ако остана с default path-а на инсталацията, в кои папки трябва да ги копирам?
; ------------------------
; SLAVE.INI
; Slave Configuration File
; ------------------------
;

[General]

LoggingPath=c:\         ; Path for CiderPrintf() log files (default is current working directory ".").
                        ; Note: if set, this line must appear before "Logging=" below.

Logging=Off             ; CiderPrintf() logging options:
                        ;   Logging=LogToFile, generate cider0.log, cider1.log etc.
                        ;   Logging=LogToCaesarTrace, log to CAESAR trace file via DebugLine(), debug level=1
                        ;   Logging=Off (default)

CPULoadReduction=TRUE   ; Set this to TRUE to reduce CPU load

;ReleaseLogDir=L:\csr\data\driver  ; Directory to save Release.log file
;NetworkLogDir=C:\       ; Directory to save caesar_network.log file

GPDInterpreterCheckLevel=0            ; 0:Off, 1:Check Pointer, 2:Check OpCodes,Variables, 3:all
DiagJobInterpreterCheckLevel=0        ; 0:Off, 1:Check Pointer, 2:Check OpCodes,Variables, 3:all
GPDInterpreterCheckPrompt=FALSE       ; TRUE: Show an error prompt, if failure is detected
DiagJobInterpreterCheckPrompt=FALSE   ; TRUE: Show an error prompt, if failure is detected

; -------------------
; PartA configuration
; -------------------

[PartA]

TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)
Monitoring=TRUE         ; Monitoring active (=FALSE, not active)
CANWarningCheck=TRUE    ; Firmware returns CAN Controller Errors (=FALSE, disabled)
DebugLevel=1            ; GPD Debug function (enable=1 disable=0)

Interrupt=188           ; DOS only, default: 188


; -------------------
; PartC configuration
; -------------------

[PartC]
;
; Default section:
;
TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)
CANWarningCheck=FALSE   ; Firmware returns CAN Controller Errors (=FALSE, deactivated)
DebugLevel=0            ; GPD Debug function (enable=1 disable=0)

MasterAddress=0xd2000   ; DOS only, default: 0xd2000
SlaveAddress=0xd4000    ; DOS only, default: 0xd4000
Interrupt=4             ; DOS only, default: 0x04

;
; Module section (Module0..Module11)
;
[PartC Module0]
Monitoring=TRUE
TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)

; -------------------
; PartD configuration
; -------------------

[PartD]

TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=2      ; max. 2 Channels with CaesarGo-Firmware (1 to 4 allowed, 2 is default)
Monitoring=TRUE         ; Monitoring activated (=FALSE, deactivated)
CANWarningCheck=FALSE   ; Firmware returns CAN Controller Errors (=FALSE, deactivated)

Com=1                   ; COM port

; -------------------
; PartJ configuration
; -------------------

[PartJ]
PassThruVersion="04.04"                   ; should be "02.02" or "04.04"
DeviceName="I+ME ACTIA - PassThru+ XS" ; only usable for 04.04 e.g. "Drew Technologies Inc. - CarDAQ" or "I+ME ACTIA - PassThru+ XS"
;FunctionLibraryRegistryKeyName="FunctionLibrary" ; only usable for 04.04

; -------------------
; PartX configuration
; -------------------

[PartX]

TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)
CANWarningCheck=FALSE   ; Firmware returns CAN Controller Errors (=FALSE, deactivated)

ServerAdr=192.168.0.12  ; PartX IP address (192.168.1.2) endian!
ControlPort=4000        ; Control port
SlavePortBase=4101      ; Slave channel port base


; -------------------
; PartY configuration
; -------------------

[PartY]

Com=1                   ; COM port for RS232 operation
Interface=USB           ; RS232|USB|AUTO (AUTO versucht zun?st USB zu nutzen, dann V24)
TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)
Monitoring=TRUE         ; Monitoring activated (=FALSE, deactivated)
CANWarningCheck=TRUE    ; Firmware returns CAN Controller Errors (=FALSE, deactivated)


; --------------------
; SDconnect configuration
; --------------------

[PartW]

TLSlaveChannels=100     ; max. 100 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)
CANWarningCheck=FALSE   ; Firmware returns CAN Controller Errors (=FALSE, deactivated)
;PredeleteFlash=TRUE    ; TRUE or 1: Delete CaesarEngine flashdisk always, 2: Delete CE flashdisk in error case, 3: Delete and dump CE flashdisk in error case
PacketDelay=0           ; Not used.
ControlPort=4000        ; TCP port, UDP is on ControlPort+1.
Protocol=TCP            ; TCP or UDP, default is TCP. Note that UDP has custom error handling.
LocateAttempts=1        ; Number of attempts at locating VCI, default is 1.
IPResyncAttempts=8      ; Deprecated.
                        ; Number of attempts to resynchronize TCP or UDP communication,
                        ; default is 8. Note that application response timeouts should be
                        ; greater than IPResyncAttempts*IPReceiveTimeout.
                        ;
                        ; If IPResyncAttempts!=0, CSVR on PowerEngine implements a 6s timeout on TCP
                        ; receive. If the receive times out (or a TCPIP error is registered), the
                        ; socket is closed and CSVR then waits for a new connect. PC sends keepalive
                        ; messages every 2s.
                        ;
                        ; If IPResyncAttempts==0, CSVR on PowerEngine maintains no timeout on TCP
                        ; receive. If a TCPIP error is registered, the socket is closed and CSVR
                        ; then waits for a new connect.
ToolkitChannelNumber=1  ; SDDCDI toolkit channel number. Default is 1.
ToolkitConnectTimeout=360000        ; Timeout awaiting completion of toolkit connection (allow for
                                    ; update time in DCDIToolkitConnectTesterToVCI())
;ForceAdapterCode=81                ; Test purpose, force usage of specific cable
FlashIntegrityCheck=TRUE            ; Check integrity of CE flash on startup. Default is TRUE.
ReportErrorOnLowVBatt=TRUE          ; Report SI_IP_LOW_VBATT_ERR error if PE measures VBatt<2V.
                                    ; Default is FALSE.
DeferCEResponse=TRUE                ; Set this to TRUE to reduce network load.
ReportFlashIntegrityFailure=TRUE    ; Report integrity error of CE flash on startup. If TRUE,
                                    ; SI_VCI_FLASH_CRC_ERR is reported on flash integrity check
                                    ; failure. Default is FALSE.

;MonDeviceFileSize=200000 ; powerEngine CAN monitor file size
;MonDeviceBlockSize=4000  ; Zip block size
;MonDeviceCompress=1      ; Zip compression type (0 for none, 1 for space, 2 for speed)
;MonitoringLogPath=c:\userdata\       ; Directory for monitoring files
;MonitoringLog=CAN1|CAN2|KLine1|KLine2 ; Set this to enable monitoring to file (takes precedence over
                                      ; powerEngine CAN monitoring)

IPReceiveTimeout=4000     ; Timeout awaiting an IP response telegram, default is 2000. A global error
                          ; flag is set with SI_IP_TIMEOUT_ERR when when this timeout occurs (see
                          ; AbortOnTCPError=TRUE below).

AbortOnTCPError=TRUE      ; Set CR254 global error on TCP error. The error is then always returned by
                          ; slave interface functions until reset on the next com-construct.

VoltageOnTCPError=0             ; Voltage reported on global error (mV). Set to "LastKnownGood" to
                                ; return the last valid voltage>6V.

                          ; Following are for use with networkled.dll. The first value is the
                          ; keepalive-roundtrip threshold (ms) for yellow, the second for red.
LANActivityThreshold=30,500     ; Media=ethernet, default is 10,500 (t<10 green, t<500 yellow,
                                ; otherwise red
WLANActivityThreshold=30,500    ; Media=WLAN, default is 10,500

                          ; Following is for use with networkled.dll. A Sleep(50) delay is measured
                          ; within timeBeginPeriod(1) and timeEndPeriod(1). The first value is the
                          ; threshold for yellow, the second for red.
CPUActivityThreshold=60,200     ; Default is 60,200 (t<60 green, t<200 yellow, otherwise red)
PingActivityThreshold=10,500    ; Default is 10,500 (t<10 green, t<500 yellow, otherwise red)

; ---------------------
; VCIPlus configuration
; ---------------------

[PartV]

; 50 Kanдle mit TL-Slave
TLSlaveChannels=50
; 4 Kanдle mit CaesarGo-Slave (1 bis 4 sind mцglich, 2 ist default)
CaesarGoChannels=4
; Monitoring aktiviert (=FALSE, deaktiviert)
Monitoring=TRUE
; Firmware returns CAN Controller Errors (=FALSE, disabled)
CANWarningCheck=TRUE
; GPD Debug function (enable=1 disable=0)
DebugLevel=1
ReportErrorOnLowVBatt=TRUE          ; Report SI_IP_LOW_VBATT_ERR error if PE measures VBatt<2V.

; -----------------------
; Spartacus configuration
; -----------------------

[Spartacus]

TLSlaveChannels=50      ; max. 50 Channels with TL-Slave Firmware
CaesarGoChannels=4      ; max. 4 Channels with CaesarGo-Firmware (1 to 4 allowed, 4 is default)
Monitoring=FALSE        ; Monitoring activated (=FALSE, deactivated)


; --------------------------
; MVCI PDU-API configuration
; --------------------------

[MVCI_Device]
;RootPath=C:\CAESAR_MUT3_root_file.xml  ; PDU-API ROOT FILENAME with Path
DeviceOptions=""
RootPath="C:\ProgramData\Vediamo\PDU\IME\PDU\RDF_CSR_I+ME_ACTIA_XS.xml"


; ---------------------------------------------------------------------------
; CABLE/ADAPTER INFORMATION
;
; AdapterCode: code issued by slave to indicate which hardware is connected
;
; DeviceType: specified in GPD #pragma DeviceType
; DeviceNumber: number of these devices/controllers
;
; DriverType: specified in GPD #pragma DriverType
; DriverNumber: numbered through 1..n
;
; AvailableChannels: max. number of comunication channels available with this
;          device
; MuxPins: highest available (KLine) mux pin, (0==no mux connected)
;          see corresponding entry for Cabletype in mapping.plf
; ---------------------------------------------------------------------------


; ------------
; PartC Cables
; ------------

[PartC_38PinCable]  ; 38-pole cable
AdapterCode=        7
DeviceType=         Uart    , Uart    , CAN
DeviceNumber=       1       , 2       , 1
DriverType=         KLine   , KLine   , CANHS
DriverNumber=       1       , 2       , 1
AvailableChannels=  1       , 1       , 50
MuxPins=            35      , 35      , 0
HardwarePins=       0       , 0       , 41:40

[PartC_OBD2Cable]   ; OBD2 cable
AdapterCode=        6
DeviceType=         Uart    , Uart    , CAN
DeviceNumber=       1       , 2       , 1
DriverType=         KLine   , KLine   , CANHS
DriverNumber=       1       , 2       , 1
AvailableChannels=  1       , 1       , 50
MuxPins=            15      , 15      , 0
HardwarePins=       0       , 0       , 41:40


; ------------
; PartD Cables
; ------------

[PartD_4PinCable]   ; 4-pole cable
AdapterCode=        10
DeviceType=         Uart
DeviceNumber=       1
DriverType=         KLine
DriverNumber=       1
AvailableChannels=  1
MuxPins=            1
HardwarePins=       0

;[PartD_Plug14]   ; 14-pole NFZ cable
;AdapterCode=        ?
;DeviceType=         Uart    , Uart
;DeviceNumber=       1       , 2
;DriverType=         KLine   , KLine
;DriverNumber=       1       , 2
;AvailableChannels=  1       , 1
;MuxPins=            11      , 11

[PartD_OBD2Cable]   ; OBD2 cable
AdapterCode=        1
DeviceType=         Uart    , Uart    , CAN
DeviceNumber=       1       , 2       , 1
DriverType=         KLine   , KLine   , CANHS
DriverNumber=       1       , 2       , 1
AvailableChannels=  1       , 1       , 50
MuxPins=            15      , 15      , 0
HardwarePins=       0       , 0       , 41:40

[PartD_C38]         ; 38-pole cable
AdapterCode=        0
DeviceType=         Uart    , Uart
DeviceNumber=       1       , 2
DriverType=         KLine   , KLine
DriverNumber=       1       , 2
AvailableChannels=  1       , 1
MuxPins=            35      , 35
HardwarePins=       0       , 0

[PartD_OBD2CANTER]  ; OBD2 cable FUSO Canter
AdapterCode=        81
DeviceType=         Uart    , Uart    , CAN
DeviceNumber=       1       , 2       , 1
DriverType=         KLine   , KLine   , CANHS
DriverNumber=       1       , 2       , 1
AvailableChannels=  1       , 1       , 50
MuxPins=            15      , 15      , 0
HardwarePins=       0       , 0       , 41:40

; ------------
; PartW Cables
; ------------

[PartW_MonitorCable]; 4-pole/can cable
AdapterCode=        3
DeviceType=         Uart    , CAN     , CAN     , CAN
DeviceNumber=       1       , 1       , 2       , 2,
DriverType=         KLine   , CANHS   , CANHS   , CANLS
DriverNumber=       1       , 1       , 2       , 2
AvailableChannels=  1       , 100     , 100     , 100
MuxPins=            40      , 0       , 0       , 0
HardwarePins=       0       , 5:6     , 7:8     , 7:8

[PartW_Plug14]      ; 14-pole NFZ cable
AdapterCode=        2
DeviceType=         Uart    , Uart
DeviceNumber=       1       , 2
DriverType=         KLine   , KLine
DriverNumber=       1       , 2
AvailableChannels=  1       , 1
MuxPins=            15      , 15
HardwarePins=       0       , 0

[PartW_OBD2Cable]   ; OBD2 cable
AdapterCode=        1
DeviceType=         Uart    , Uart    , CAN     , CAN     , CAN     , Uart    , SSI
DeviceNumber=       1       , 2       , 1       , 2       , 2,      , 2       , 2
DriverType=         KLine   , KLine   , CANHS   , CANHS   , CANLS   , J1708   , J1708
DriverNumber=       1       , 2       , 1       , 2       , 2       , 2       , 1
AvailableChannels=  1       , 1       , 100     , 100     , 100     , 1       , 10
MuxPins=            15      , 15      , 0       , 0       , 0       , 0       , 0
HardwarePins=       0       , 0       , 6:14    , 12:13   , 12:13   , 3:11    , 3:11

[PartW_C38]         ; 38-pole cable
AdapterCode=        0
DeviceType=         Uart    , Uart
DeviceNumber=       1       , 2
DriverType=         KLine   , KLine
DriverNumber=       1       , 2
AvailableChannels=  1       , 1
MuxPins=            40      , 40
HardwarePins=       0       , 0

[PartW_Breakout]    ; Test adapter breakout box
AdapterCode=        4
DeviceType=         Uart    , Uart    , CAN     , CAN     , CAN     , Uart    , SSI     , SSI
DeviceNumber=       1       , 2       , 1       , 2       , 2,      , 2       , 1       , 2
DriverType=         KLine   , KLine   , CANHS   , CANHS   , CANLS   , J1708   , J1850   , J1708
DriverNumber=       1       , 2       , 1       , 2       , 2       , 2       , 1       , 1
AvailableChannels=  1       , 1       , 100     , 100     , 100     , 1       , 4       , 10
MuxPins=            35      , 35      , 0       , 0       , 0       , 0       , 0       , 0
HardwarePins=       0       , 0       , 41:40   , 0:0     , 0:0     , 3:11    , 2       , 3:11

[PartW_OBD2DOIPCable]   ; OBD2/DOIP cable
AdapterCode=        16
DeviceType=         Uart    , Uart    , CAN     , CAN     , CAN
DeviceNumber=       1       , 2       , 1       , 2       , 2,
DriverType=         KLine   , KLine   , CANHS   , CANHS   , CANLS
DriverNumber=       1       , 2       , 1       , 2       , 2
AvailableChannels=  1       , 1       , 100     , 100     , 100
MuxPins=            15      , 15      , 0       , 0       , 0
HardwarePins=       0       , 0       , 6:14    , 12:13   , 12:13

[PartW_OBD2CANTER]  ; OBD2 cable FUSO Canter
AdapterCode=        81
DeviceType=         Uart    , Uart    , CAN     , Uart
DeviceNumber=       1       , 2       , 1       , 2
DriverType=         KLine   , KLine   , CANHS   , MMCSCM
DriverNumber=       1       , 2       , 1       , 2
AvailableChannels=  1       , 1       , 50      , 1
MuxPins=            20      , 20      , 0       , 3
HardwarePins=       0       , 0       , 41:40   , [11,12,13]

[PartW_PulseConverterCable]  ; PulseConverter cable FUSO Canter
AdapterCode=        82
DeviceType=         Uart    , Uart    , CAN     , Uart
DeviceNumber=       1       , 2       , 1       , 2
DriverType=         KLine   , KLine   , CANHS   , MMCSCM
DriverNumber=       1       , 2       , 1       , 2
AvailableChannels=  1       , 1       , 50      , 1
MuxPins=            15      , 15      , 0       , 3
HardwarePins=       0       , 0       , 41:40   , [11,12,13]

; ------------
; PartV Cables
; ------------

[PartV_C38]         ; 38-pole cable
AdapterCode=        0
DeviceType=         Uart    , Uart
DeviceNumber=       1       , 2
DriverType=         KLine   , KLine
DriverNumber=       1       , 2
AvailableChannels=  1       , 1
MuxPins=            40      , 40
HardwarePins=       0       , 0

[PartV_OBD2Cable]   ; OBD2 cable
AdapterCode=        1
DeviceType=         Uart    , Uart    , CAN     , CAN     , CAN     , Uart
DeviceNumber=       1       , 2       , 1       , 2       , 2,      , 2
DriverType=         KLine   , KLine   , CANHS   , CANHS   , CANLS   , J1708
DriverNumber=       1       , 2       , 1       , 2       , 2       , 2
AvailableChannels=  1       , 1       , 100     , 100     , 100     , 1
MuxPins=            15      , 15      , 0       , 0       , 0       , 0
HardwarePins=       0       , 0       , 6:14    , 12:13   , 12:13   , 3:11

[PartV_Plug14]      ; 14-pole NFZ cable
AdapterCode=        2
DeviceType=         Uart    , Uart
DeviceNumber=       1       , 2
DriverType=         KLine   , KLine
DriverNumber=       1       , 2
AvailableChannels=  1       , 1
MuxPins=            15      , 15
HardwarePins=       0       , 0

[PartV_MonitorCable]; 4-pole/can cable
AdapterCode=        3
DeviceType=         Uart    , CAN     , CAN     , CAN
DeviceNumber=       1       , 1       , 2       , 2
DriverType=         KLine   , CANHS   , CANHS   , CANLS
DriverNumber=       1       , 1       , 2       , 2
AvailableChannels=  1       , 100     , 100     , 100
MuxPins=            40      , 0       , 0       , 0
HardwarePins=       0       , 5:6     , 7:8     , 7:8

[PartV_Breakout]    ; Test adapter breakout box
AdapterCode=        4
DeviceType=         Uart    , Uart    , CAN     , CAN     , CAN     , Uart    , SSI
DeviceNumber=       1       , 2       , 1       , 2       , 2,      , 2       , 1
DriverType=         KLine   , KLine   , CANHS   , CANHS   , CANLS   , J1708   , J1850
DriverNumber=       1       , 2       , 1       , 2       , 2       , 2       , 1
AvailableChannels=  1       , 1       , 100     , 100     , 100     , 1       , 4
MuxPins=            35      , 35      , 0       , 0       , 0       , 0       , 0
HardwarePins=       0       , 0       , 41:40   , 0:0     , 0:0     , 3:11    , 2

[PartV_OBD2DOIPCable]   ; OBD2/DOIP cable
AdapterCode=        16
DeviceType=         Uart    , Uart    , CAN     , CAN     , CAN
DeviceNumber=       1       , 2       , 1       , 2       , 2
DriverType=         KLine   , KLine   , CANHS   , CANHS   , CANLS
DriverNumber=       1       , 2       , 1       , 2       , 2
AvailableChannels=  1       , 1       , 100     , 100     , 100
MuxPins=            15      , 15      , 0       , 0       , 0
HardwarePins=       0       , 0       , 6:14    , 12:13   , 12:13

[PartV_OBD2CANTER]  ; OBD2 cable FUSO Canter
AdapterCode=        81
DeviceType=         Uart    , Uart    , CAN     , Uart
DeviceNumber=       1       , 2       , 1       , 2
DriverType=         KLine   , KLine   , CANHS   , MMCSCM
DriverNumber=       1       , 2       , 1       , 2
AvailableChannels=  1       , 1       , 50      , 1
MuxPins=            20      , 20      , 0       , 3
HardwarePins=       0       , 0       , 41:40   , [11,12,13]

[PartV_PulseConverterCable]  ; PulseConverter cable FUSO Canter
AdapterCode=        82
DeviceType=         Uart    , Uart    , CAN     , Uart
DeviceNumber=       1       , 2       , 1       , 2
DriverType=         KLine   , KLine   , CANHS   , MMCSCM
DriverNumber=       1       , 2       , 1       , 2
AvailableChannels=  1       , 1       , 50      , 1
MuxPins=            15      , 15      , 0       , 3
HardwarePins=       0       , 0       , 41:40   , [11,12,13]